Dynatrace Hub - Generic Cisco Device latest releases

Generic Cisco Device 3.5.0

Wed, 04 Mar 2026 15:42:03 +0000

⚠️ Metric com.dynatrace.extension.network_device.lldp_neighbor was renamed to com.dynatrace.extension.snmp-generic-cisco-device.lldp_neighbor to avoid conflicts with generic network topology rules

Changes

Require all dimensions exist for entity creation
Update latest dashboard to use link to IO App Network view for listing entities

Fixes

sys.name and mac.address dimensions are required on all network metrics and filtered for empty values. This caused unnecessary stress on topology engine
Update Cisco interface entity to only use (and require sys.name OID)
- Previous version required device.name which would not be available if the IP address cannot be resolved via DNS

Generic Cisco Device 3.4.1

Fri, 19 Dec 2025 17:00:43 +0000

✨ New in this version:

Add Davis anomaly detector templates to extension package

Generic Cisco Device 3.4.0

Thu, 04 Dec 2025 14:42:18 +0000

⚠️ IMPORTANT: This version requires a minimum Dynatrace version of `1.318`

✨ New in this version (3.4.0):

Added the following new metrics to the Advanced interfaces feature set
- com.dynatrace.extension.network_device.if.in.multicast_pkts.count
- com.dynatrace.extension.network_device.if.out.multicast_pkts.count
- com.dynatrace.extension.network_device.if.in.broadcast_pkts.count
- com.dynatrace.extension.network_device.if.out.broadcast_pkts.count
- com.dynatrace.extension.network_device.if.in.ucast_pkts.count
- com.dynatrace.extension.network_device.if.out.ucast_pkts.count

Generic Cisco Device 3.3.1

Tue, 25 Nov 2025 11:41:18 +0000

Changed in this version

network:interface entities created by the extension are named after the ifName (name) OID instead of ifDescr (description) OID. This resolves an issue with Network Neighbors not correctly related at interface level

⚠️ Note: any settings/configuration based on the names of network:interface entities may need adjusting due to the above change

Generic Cisco Device 3.3.0

Wed, 19 Nov 2025 13:57:44 +0000

✨ New in this version (3.3.0):

Added the following metrics to the new Advanced interfaces feature set:
- com.dynatrace.extension.network_device.if.lastchange
- com.dynatrace.extension.network_device.if.in.crc_errors

Generic Cisco Device 3.2.7

Wed, 17 Sep 2025 16:15:47 +0000

Removes the below metrics from the default feature set and moves them to a new Control plane feature set
- com.dynatrace.extension.snmp-generic-cisco-device.sys.uptime
- com.dynatrace.extension.snmp-generic-cisco-device.cpm.cpu.total.1min.rev
- com.dynatrace.extension.snmp-generic-cisco-device.cpm.cpu.loadavg.1min
- com.dynatrace.extension.snmp-generic-cisco-device.cpm.cpu.memory.hc.used
- com.dynatrace.extension.snmp-generic-cisco-device.cpm.cpu.memory.hc.free
- com.dynatrace.extension.snmp-generic-cisco-device.cpm.cpu.memory.used
- com.dynatrace.extension.snmp-generic-cisco-device.cpm.cpu.memory.free

Generic Cisco Device 3.2.5

Thu, 28 Aug 2025 15:01:59 +0000

Minimum Dynatrace version: 1.310

Minimum ActiveGate version: 1.307

Changes

Adds BGP peer connection established time to "BGP" feature set

Generic Cisco Device 3.2.3

Mon, 28 Jul 2025 08:28:55 +0000

⚠️ IMPORTANT CHANGE:

Metrics in "default" feature set will always be enabled and cannot be disabled. These metrics are mandatory. Take extra caution configuring devices and interfaces for which you are collecting data. Make use of Interface filters to limit the number of interfaces, otherwise, all interfaces on the device will be collected by default. In case you do not wish to collect interfaces on your device, enter $eq(!) in the "Interface Name" filter field on the Feature Sets screen during configuration.

These metrics introduced into the "default" feature set are per interface and cannot be disabled but can be filtered.

com.dynatrace.extension.network_device.if.bytes_in.count
com.dynatrace.extension.network_device.if.bytes_out.count
com.dynatrace.extension.network_device.if.in.errors.count
com.dynatrace.extension.network_device.if.in.discards.count
com.dynatrace.extension.network_device.if.out.errors.count
com.dynatrace.extension.network_device.if.out.discards.count

✨ New in this version:

Adds dt.security_context to network:device, network:interface, snmp:com_dynatrace_extension_snmp_generic_cisco_device, and snmp:com_dynatrace_extension_snmp_generic_cisco_network_interface entities

Generic Cisco Device 3.2.1

Thu, 12 Jun 2025 16:09:17 +0000

Notice:

If upgrading to this version from version 2.x.x, please read the release notes for version 3.1.0 first, before upgrading.

🪲 Fixed in this version:

Removed duplicate cards on Unified Analysis screens related to FRU feature set.

Generic Cisco Device 3.1.0

Wed, 26 Mar 2025 15:49:28 +0000

Major version update - please review release notes fully

Breaking changes

In order to support some BGP data that comes from the non-Cisco BGP MIB, the existing BGP feature set was renamed to "Cisco BGP" and the new data is under "BGP". Configurations will be able to be updated without re-creation, but if you were using the BGP feature set you must enable the Cisco BGP feature set in order to keep collecting that data.

New features

Several new feature sets for network peer metrics (feature sets named accordingly)
- BGP (BGP4-MIB)
- OSPF (OSPF-MIB)
- EIGRP (CISCO-EIGRP-MIB)
New FRUs (Field Replaceable Units) feature set
- Fan and PSU statuses
- From CISCO-ENTITY-FRU-CONTROL-MIB
CRC (Cyclic Redundancy Checksum) Errors metric is added to the Interfaces feature set
Advanced sensors
- New feature set that can report the 'raw' sensor values and statuses for sensors available in CISCO-ENTITY-SENSOR-MIB
- Because all sensor types are reported via the same OID, there is no way to properly set metadata
- Use the available dimensions to properly filter and make use of the values for the needed use cases
New gen3 dashboard added

Generic Cisco Device 2.3.11

Thu, 09 Jan 2025 02:10:53 +0000

Fixed in this version:

Minimum schema requirement correctly enforced

New in this version:

Network neighbor discovery through LLDP
UI is compatible with AppEngine use

Generic Cisco Device 2.1.6

Fri, 26 Jul 2024 11:37:23 +0000

Fixed in this version:

Recently introduced metrics for device and interface now apply the existing feature sets and filters to reduce license consumption.

Generic Cisco Device 2.1.4

Tue, 02 Jul 2024 15:17:38 +0000

New entities and metrics were added to represent Cisco as a network device for the SNMP Autodiscovery Extension
Ability to filter interfaces by their alias and type
Several new feature-sets for new capabilities:
- Memory pools
- BGP
- High availability status
Change to use '1 min' load values instead of '5 min' to align with extension frequency
Non-high capacity memory values collected for cases when high-capacity OIDs not available

Generic Cisco Device 1.12.3

Tue, 12 Mar 2024 18:09:59 +0000

🪲 Fixed in this version:

Network interface charts would not display due to incorrect splitting

Generic Cisco Device 1.12.2

Wed, 10 Jan 2024 13:04:54 +0000

✨ New in this version:

Cisco Stack model and serial number reported as device attributes
Device software revision (version) reported as attribute
Power supply status available via new feature set

Generic Cisco Device 1.12.1

Fri, 05 Jan 2024 12:38:21 +0000

🚀 Improved in this version:

Configuration fields for filtering now support up to 5000 characters

Generic Cisco Device 1.12.0

Wed, 19 Jul 2023 10:36:19 +0000

Fixed: Cisco Network Interface metrics not visible in a Management Zone.

Generic Cisco Device 1.11.0

Mon, 17 Apr 2023 10:20:08 +0000

High capacity interface traffic metrics extracted to "Interfaces 64-bit" feature set.
Default interface traffic metrics extracted to "Interfaces 32-bit" feature set.

Check distribution of metrics in the new feature sets to avoid gaps in the data

Generic Cisco Device 1.10.0

Fri, 10 Feb 2023 10:08:18 +0000

Changes:

removed a rule for creating an entity from snmp traps. Now traps source entity is connected to cisco device entity only with SAME_AS relation.

Generic Cisco Device 1.9.0

Wed, 01 Feb 2023 10:42:58 +0000

v1.9.0

Added 4 new metrics:
- Octets received (high capacity)
- Octets transmitted (high capacity)
- Interface outgoing traffic (high capacity)
- Interface incoming traffic (high capacity)
Bandwidth utilization is now calculated using above metrics

Dynatrace Hub - Generic Cisco Device latest releases

Generic Cisco Device 3.5.0

Changes

Fixes

Generic Cisco Device 3.4.1

Generic Cisco Device 3.4.0

⚠️ IMPORTANT: This version requires a minimum Dynatrace version of 1.318

✨ New in this version (3.4.0):

Generic Cisco Device 3.3.1

Changed in this version

Generic Cisco Device 3.3.0

✨ New in this version (3.3.0):

Generic Cisco Device 3.2.7

Generic Cisco Device 3.2.5

Minimum Dynatrace version: 1.310

Minimum ActiveGate version: 1.307

Changes

Generic Cisco Device 3.2.3

⚠️ IMPORTANT CHANGE:

✨ New in this version:

Generic Cisco Device 3.2.1

Notice:

🪲 Fixed in this version:

Generic Cisco Device 3.1.0

Major version update - please review release notes fully

Breaking changes

New features

Generic Cisco Device 2.3.11

Fixed in this version:

New in this version:

Generic Cisco Device 2.1.6

Fixed in this version:

Generic Cisco Device 2.1.4

Generic Cisco Device 1.12.3

🪲 Fixed in this version:

Generic Cisco Device 1.12.2

✨ New in this version:

Generic Cisco Device 1.12.1

🚀 Improved in this version:

Generic Cisco Device 1.12.0

Generic Cisco Device 1.11.0

Check distribution of metrics in the new feature sets to avoid gaps in the data

Generic Cisco Device 1.10.0

Generic Cisco Device 1.9.0

v1.9.0

⚠️ IMPORTANT: This version requires a minimum Dynatrace version of `1.318`